ST-LINK V2 programmer for STM8/STM32 processors (clone)

Available:Preorder

Product MPN: 14565
Category:- Power supply boards DC, LC filters,- Programmers,All products,Drone/drone system,Radio products and modules

€4,99

Pre-order

ST-LINK V2 is a USB programmer/debugger for all STM32SWD and STM8SWIM series processors manufactured by STMicroelectronics.

Note: the color of the case may differ from the picture (red, yellow, black, etc.).

Key features

Support for STM32 controllers with SWD debug interface
Support STM8 controllers with SWIM debug interface
Supported software versions:
- U XTW LINK ST Utility 2.0 and higher
- STVD 4.2.1 and higher
- STVP 3.2.3 and higher
- IAR EWARM V6.20 or higher
- IAR EWSTM8 V1.30 or higher
- KEIL RVMDK V4.21 or higher
Supports automatic firmware update. The factory firmware has been updated to V2.J17.S4
Interface designation is directly marked on the housing
Increase output power up to 5V
U-shaped aluminum alloy housing to protect the motherboard. Pin designation is directly marked on the housing.
Internal motherboard is equipped with a 500mA fuse
Two-color LED indicator that allows you to monitor the operating status of ST-LINK V2

ST-LINK V2 is a USB programmer/debugger for all STM32SWD and STM8SWIM series processors manufactured by STMicroelectronics.

Note: the color of the case may differ from the picture (red, yellow, black, etc.).

Key features

Support for STM32 controllers with SWD debug interface
Support STM8 controllers with SWIM debug interface
Supported software versions:
- U XTW LINK ST Utility 2.0 and higher
- STVD 4.2.1 and higher
- STVP 3.2.3 and higher
- IAR EWARM V6.20 or higher
- IAR EWSTM8 V1.30 or higher
- KEIL RVMDK V4.21 or higher
Supports automatic firmware update. The factory firmware has been updated to V2.J17.S4
Interface designation is directly marked on the housing
Increase output power up to 5V
U-shaped aluminum alloy housing to protect the motherboard. Pin designation is directly marked on the housing.
Internal motherboard is equipped with a 500mA fuse
Two-color LED indicator that allows you to monitor the operating status of ST-LINK V2

Processor: STM32F103C8T6
Three working programmer interfaces: JTAG (Joint Test Action Group), SWIM (Single Wire Interface Module) and SWD (Serial Wire Debug).
Connection interface: USB 2.0 / 2.54" pins
SWIM interface voltage adjustment: 1.65 - 5.5V
Support different modes in SWIM interface
- low-speed 9.7 Kb/sec
- high-speed 12.8 Kb/sec
Programming voltage for SWD and JTAG interfaces: 1.65 - 3.6V
Firmware update: DFU (Direct firmware update) function
Dimensions: 6.5 x 2.5 x 1.5 cm
Weight: 19g

RECOMMENDATIONS

To use the programmer, you need to perform the following steps:

Download and install the drivers, which can be found on the official website of the microcontroller manufacturers.
Download and install the development and programming environment:
- if you are interested in in-circuit debugging of the STM8 microcontroller, use ST Visual Develop - STVD (version 4.1.0 or newer)
- if you are interested in in-circuit programming of STM8 microcontroller, use ST Visual Program - STVP (version 3.1.0 or newer).
- if you are interested in STM32 microcontroller programming and debugging, you can use the following programs: IAR toolset EWARM (version 5.30 or later), Atollic toolset TrueSTUDIO (version 1.0 or later), Keil toolset ARM-MDK (version 3.3 or later), TASKING or utilities downloaded from official sites
Connect the programmer to the PC. Connect directly to the computer's USB port. When you connect the programmer, the PC OS will detect the device and drivers by itself, provided that you have installed the drivers beforehand. If the automatic installation of drivers has not started, start it manually through the OS Hardware Manager.
Before starting programming or debugging it is necessary to run and configure the software for the programmer.
The software is compatible with Win 2000, WIN 2003, Win XP, WIN 2008, WIN 7, WIN Vista, WIN 8, WIN 10 (32-bit and 64-bit).
Connect the device to be programmed to the programmer. Use a four-core cable with BLS-1 connectors at both ends (the cable is included in the package).
The ST-LINK V2 USB programmer has a ten-pin connector for BLS connectors (the distance between the pins is 2.54 mm). Three working interfaces of the programmer: JTAG (Joint Test Action Group), SWIM (Single Wire Interface Module) and SWD (Serial Wire Debug).